Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Lakewood?
Gate installation in Lakewood typically runs $2,400 to $6,800 for a residential automatic gate, with most single-swing driveway gates landing around $3,900 once the operator, safety sensors, and wiring are counted. A basic manual pedestrian gate is a much smaller job, usually $900 to $2,100 installed. Commercial slide gates and wide double-swing entrances climb past $9,500 because the panels are heavier and the operator has to be sized for constant duty, not occasional use.
Those numbers move in either direction depending on gate width, whether an operator already exists, and how much concrete work the posts need. Below is a 2026 line-item breakdown for the Lakewood market, followed by the factors that push a quote up or keep it down. If you want a firm number instead of a range, that’s what a free on-site estimate is for.
Key Takeaways
- Most residential automatic gate installs in Lakewood fall between $2,400 and $6,800.
- Manual pedestrian gates are usually $900 to $2,100 installed.
- The operator and its wiring often cost as much as the gate itself.
- Post footings and concrete are the most common line item that surprises homeowners.
- We install and automate gates with systems from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
Gate Installation Cost Breakdown (2026)
The table below shows typical installed ranges for each part of a gate project. These are estimates, not quotes; the written estimate you get after we look at your property sets the final price.
| Line item | Typical installed range | What it covers |
|---|---|---|
| Manual pedestrian gate (steel or aluminum) | $900 – $2,100 | Gate leaf, hinges, latch, posts set in concrete |
| Manual single-swing driveway gate | $1,800 – $3,800 | Wider leaf, heavy-duty hinges, latch or lock, post footings |
| Swing gate operator (residential) | $1,100 – $2,400 | Motor, control board, arm or actuator, basic safety devices |
| Slide gate operator (residential) | $1,400 – $3,200 | Motor, track and rollers, rack, control board, safety edges |
| Electrical run to the gate | $400 – $1,600 | Conduit and wiring from the panel to the operator, trenching included |
| Post footings and concrete | $300 – $900 | Digging, concrete, setting and curing time |
| Entry keypad or access control | $250 – $850 | Keypad, intercom, or card reader wiring and setup |
| Safety sensors and reversing edges | $180 – $550 | Photo-eye or edge sensors, tested after install |
| Commercial slide gate operator | $3,200 – $7,500 | Constant-duty motor, loop detectors, heavier controls |
| Double-swing or wide slide gate system | $5,200 – $12,000+ | Wider panels, two operators or a large single, heavier anchoring |
The pattern you’ll notice is that the gate itself is rarely the largest line. On a typical automatic driveway gate, the operator, the electrical run, and the safety devices together often cost as much as the gate panels. A simple manual gate is mostly hardware and labor. Once you add automation, you’re really buying a small electrical system with a gate hanging off it, and the quote reflects that. That’s also why a general handyman and a gate specialist often land in different places on price: the electronics work is where the job can quietly go wrong.
What Affects Gate Installation Pricing in Lakewood
- Gate width and weight. A 4-foot pedestrian gate and a 16-foot driveway gate are different animals. Wider, heavier leaves need bigger hinges, thicker posts, and deeper footings, and they require a more powerful operator to move them safely.
- Whether an operator already exists. If you’re replacing a gate on an existing automated system, we may be able to reuse the operator and wiring, which trims the total. Starting from nothing means power, conduit, controls, and sensors all land in the quote.
- The electrical run. Distance from your electrical panel to the gate changes the price more than most people expect. A gate 15 feet from the panel is one job; a gate across the yard with a long trench is another. Lakewood’s older residential lots often have panels at the far side of the house, which is where this line item grows.
- Sidewalk and driveway layout. Many Lakewood homes have a driveway that runs along the property line with a narrow setback to the sidewalk. That geometry affects how a swing gate opens and whether a slide gate has room to travel. A gate that would swing into a walkway usually needs to be a slider or opened inward instead.
- Material choice. Steel and aluminum are the common choices for a reason; they hold up well in Southern California’s dry, mild climate. Wood looks good but needs more upkeep over the years, and ornamental designs with more components cost more to build and fit.
- The operator brand and duty rating. A residential swing operator and a commercial constant-duty slider are not priced the same, and they shouldn’t be. Matching the operator to how often the gate actually opens is the single best way to avoid replacing it early.
One local factor worth naming: Lakewood’s climate is mild and dry most of the year, which is good news for gate hardware but hard on anything that moves. Dust and grit work their way into tracks and hinges, and the dry sun fades and dries out finishes. That doesn’t change install price directly, but it’s a reason to choose components that are easy to service, because everything on a gate eventually needs attention.
How to Save on Gate Installation
There’s no such thing as a cheap gate that lasts, but there are real ways to keep a Lakewood installation within budget without cutting corners that cost you later.
- Reuse what’s sound. If your existing posts, operator, or wiring is in good shape, keeping it can save hundreds. We assess what can stay and what should go before quoting, rather than defaulting to a full replacement.
- Size the operator to your use, not the biggest model. A residential swing gate that opens a few times a day doesn’t need a constant-duty commercial operator. Matching the equipment to actual use keeps the price sensible and the system reliable.
- Pick a simpler gate design. Ornamental designs with lots of components cost more to build and fit than a clean, straightforward leaf. Clean lines also age better in the sun.
- Bundle access control from the start. Adding a keypad or intercom during installation costs less than retrofitting it later, because the wiring is already being run.
- Get a written estimate before work starts. Free estimates are exactly that: free. Use them to compare the scope line by line, not just the bottom number.
The biggest savings, though, come from hiring a gate specialist rather than a generalist. A gate-only company has seen the failures before and can size and install the system correctly the first time, which is the real cost saver over the life of the gate. Waverly Gate Repair has worked on gates across the local area since 2013, and our Waverly Gate Repair team focuses on nothing but gates. If you’re in Lakewood, we’d be glad to take a look at your property and give you a free estimate.
Should You Repair Your Existing Gate or Replace It?
Repair is usually the better call if the gate structure and operator are sound and the problem is isolated, such as a failing control board, a stuck arm, or a worn hinge. Replacement makes more sense when the gate panels are rusted through, the posts are loose, or the operator is old enough that parts are hard to source and the gate is fighting you every time it moves. As a rule of thumb, if a repair costs more than half of a new install and the equipment is near the end of its useful life, replacement is the smarter long-term spend. When a repair is the right answer, we fix it; when a replacement is, we tell you straight. That’s the advantage of a company that does both under one roof.
What Happens When You Call?
You call (866) 925-0168 and tell us about your gate and what you’re hoping for. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We ask about the gate width, the opening, whether there’s an existing operator, and where your electrical panel sits, because those answers shape the estimate. Then we set a time to come out, look at the site, and give you a written estimate covering the gate, the operator, the wiring, and any concrete work. From there you decide. No pressure, no surprise line items added later.
FAQs – Gate Installation Cost
How much does gate installation cost in Lakewood?
Most residential automatic gate installations in Lakewood cost between $2,400 and $6,800, with a typical single-swing driveway gate landing around $3,900 installed. Manual pedestrian gates are usually $900 to $2,100. Call (866) 925-0168 for a free estimate tailored to your property.
Is it cheaper to repair or replace a gate?
Repair is cheaper when the problem is isolated, often a few hundred dollars versus several thousand for a new system. Replacement wins when the gate structure, posts, or operator are worn out. If a repair costs more than half of a new install and the equipment is old, replace it. Call (866) 925-0168 and we’ll tell you honestly which makes sense for your gate.
How much does an automatic gate operator cost in Lakewood?
A residential swing operator typically installed runs $1,100 to $2,400, and a residential slide operator $1,400 to $3,200. Commercial constant-duty operators start around $3,200 and go up from there. Call (866) 925-0168 for an exact quote; estimates are free.
Do I need a permit to install a gate in Lakewood?
Most cities require a permit for a new gate, especially one that involves electrical work or sits near a property line, so ask the City of Lakewood’s building department before you build. Permit rules vary by property and by the height and location of the gate. Call (866) 925-0168 and we’ll walk you through what’s typically required.
Can you install the gate and wire the operator, or do I need a separate electrician?
We handle both. Electric and automated gate work is a specialty, and a gate system needs a technician who understands the mechanical and the electronics together, not one who does half the job and hands off. We install the gate, run the wiring to the operator, and set up the controls and safety sensors as one project. Call (866) 925-0168 to get started.
Why a Gate Specialist for Your Lakewood Installation
Most companies that show up to a gate job are fencing or general contracting outfits with a gate in the truck. A gate-only company brings something different: hands-on experience across the brands your system may already use. Whether your LiftMaster operator is at the end of its life, your FAAC control board needs replacing, or you’re just starting from scratch with a Linear or DoorKing system, we work on what you already have rather than steering you to a brand that suits us. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so you’re not stuck being told “we don’t work on that.”
That breadth matters for installation too. When we quote a new gate, we’re sizing an operator we know how to service and support, and that’s a better outcome for you over the life of the system. Waverly Gate Repair has focused on gates since 2013, and it’s the only thing we do. Your gate, our only focus.
Contact Us for a Free Estimate
If you’re ready to install a gate or aren’t sure whether you need a repair or a replacement, call (866) 925-0168. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A clear written estimate, an honest read on what your gate actually needs, and a specialist who knows gates inside and out. That’s what we bring to a Lakewood property. We look forward to helping you get your gate working the way it should.
Pricing reflects the Lakewood market as of 2026. Waverly Gate Repair offers free estimates – call (866) 925-0168.
Written by the team at Waverly Gate Repair, serving Lakewood since 2013.
What Our Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Chris Parker"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Brandon Wong"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Ryan Barrett