Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Lakewood?
Gate access control in Lakewood typically costs $350 to $650 for a single keypad or entry device installed on an existing operator, $900 to $1,800 for a residential system with keypad, remotes, and safety sensors added to a gate that already has power, and $2,800 to $5,500 when we’re adding an operator, access control, and wiring to a gate that has none. Repairs to a control board or a failed entry device run $180 to $450 in most cases. These are typical estimates for the Lakewood market in 2026; the written estimate we give you after we look at the gate sets the final price.
Gate Access Control Cost Breakdown (2026)
Here’s how the numbers stack up by line item. Each range is an estimate for a typical residential or small commercial gate in Lakewood, and the exact figure depends on the condition of the gate, the operator, and the wiring that’s already run.
| Line Item | Typical Cost |
|---|---|
| Keypad or entry device installed (existing operator) | $350 – $650 |
| Residential access control added to existing operator (keypad, remotes, sensors) | $900 – $1,800 |
| New operator plus access control on an unpowered gate (residential) | $2,800 – $5,500 |
| Control board or entry device repair | $180 – $450 |
| Loop detector or vehicle sensor added | $450 – $900 |
| Intercom or call station installed | $500 – $1,200 |
| Wiring for a gate that’s not pre-wired (per run, variable) | $400 – $1,500 |
| Commercial multi-tenant access (DoorKing-style entry, adds users) | $1,500 – $4,000 |
| Battery backup or surge protection added | $200 – $550 |
What pushes a Lakewood job toward the higher end? Adding access control to a gate that’s never had an operator is the biggest one, because now you’re paying for the operator, the access device, and the low-voltage wiring to get power where it needs to go. Working with a gate that’s older, out of alignment, or on a slide track that needs adjustment adds labor time, because a control system only works cleanly when the gate itself moves cleanly. Choosing a commercial-grade controller for a property with a lot of tenants or vehicles costs more than a residential keypad, but it handles more users and gives you real management controls. And if the property doesn’t have power at the gate, running that line is a real line item, not a rounding error.
The other half of the question is brand. Whether your LiftMaster operator is failing or your FAAC board needs replacing, we work on what you already have. That matters here because a big chunk of the quote in Lakewood depends on the equipment already on the property, and we’re not going to tell you we can’t service your system because we sell a different brand.
What Affects Gate Access Control Pricing in Lakewood
- Gate type: A single-swing gate is usually faster to automate than a slide gate, and slide gates need to be flat and level along their track. Access control cost tracks the gate it’s attached to, because setup and calibration take longer on anything that moves unevenly.
- Power availability at the gate: If low-voltage wire is already run to the gate, adding a keypad is a much shorter job than starting from scratch. Wired runs, conduit, and getting power where it’s needed are often the difference between a modest job and a serious one.
- Number of vehicles and users: A single family driveway needs a keypad and remotes. A small multi-tenant property in Lakewood with employees coming and going needs a call system, more entries, and a controller that can manage who has access and when. More users means more cost, but it also means more control.
- The age and condition of the gate and hardware: Automatic gates in Lakewood sit outside all year, and hinges, rollers, tracks, and operators take a beating. If the gate drags or bind, we have to fix that first, or the new access control will fault and cycle badly from day one.
- Entry method: A simple keypad is the least expensive way to add access control. Phone entry, intercom, vehicle loops, and card readers each add equipment, and each adds installation time.
- Brand and controller compatibility: Some operators accept aftermarket access devices directly and some need adapters or a specific accessory. Because we handle LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, we can tell you up front whether your existing operator will take a new entry device cleanly.
If you’re managing an automatic gate and something’s stopped working, the fastest way to get a real number is a free estimate. Call (866) 925-0168. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
How to Save on Gate Access Control
The honest answer is that most savings come from planning before anything is ordered, not from hunting for a coupon. Here’s where the money actually is.
- Fix the gate before you automate it. If the gate sags, binds, or comes off its track, that gets sorted out first. Spending a bit on hinge and track adjustment now saves you from paying a technician a second time to re-set the operator once the gate actually runs.
- Reuse what works. There’s no reason to replace a functioning operator or an existing keypad just because you’re upgrading access. We’re brand-agnostic, so we work with the equipment you already have and only replace the parts that have failed or that genuinely can’t handle what you’re adding.
- Match the access method to the property. A residential driveway rarely needs a commercial call station with dozens of entries. A small commercial property rarely gets by with a single keypad if tenants and vendors need their own codes. Choosing the right tier keeps the price in range.
- Ask for the itemized estimate. Our estimate breaks out equipment and labor so you can see what each piece costs and decide what to do now and what can wait. That’s not a sales tactic; it’s how you make a decision you don’t regret in six months.
- Call early. A small fault that gets looked at quickly is usually a small repair. The same fault left through a hot Lakewood summer and an operator cycling under load tends to grow into a control board replacement. Getting it looked at is the cheapest move in this guide.
Free estimates are part of every job we take on. Call (866) 925-0168 and we’ll set up a time to come look.
When to Repair vs. Replace Gate Access Control
Repair is usually the better call when the gate hardware, the operator, and the wiring are sound and only one component has failed – a keypad that’s stopped reading codes, a board that’s blown, a sensor that’s out of alignment. Replacement makes more sense when the operator is near the end of its life anyway, when parts are hard to source, or when the property has outgrown what the system can do. There’s no pat answer; it comes down to what’s actually failing and what everything surrounding it looks like. A technician who looks at the whole gate, not just the box on the post, can give you that answer in a single visit.
FAQs – Gate Access Control Cost
How much does gate access control cost in Lakewood?
Most residential gate access control jobs in Lakewood run $350 to $650 for a keypad installed on an existing operator, $900 to $1,800 for a fuller system with remotes and sensors, and $2,800 to $5,500 if the gate needs an operator and wiring added. Repairs to a board or entry device are usually $180 to $450. Call (866) 925-0168 for a free estimate on your gate.
Is it cheaper to repair or replace a failing access system?
Usually repairing is cheaper when a single component fails – typically $180 to $450 versus $900 to $1,800 to replace and reconfigure. Replacement becomes the better value when the operator is aging, parts aren’t available, or you need capabilities the current system can’t handle. We’ll tell you honestly which one fits your gate. Free estimates; call (866) 925-0168.
Can you add access control to a gate that has no operator yet?
Yes, and the typical all-in range is $2,800 to $5,500 for a residential gate. That covers the operator, the access device, and the low-voltage wiring to run power and control to the gate. The exact price depends on the gate type, the run to the gate, and whether there’s power nearby. Call (866) 925-0168 to get an on-site estimate.
How much does access control cost for a small commercial property in Lakewood?
Commercial multi-tenant access control typically runs $1,500 to $4,000, depending on the number of users tied to it, whether a call station or intercom is included, and whether you’re adding to an existing DoorKing or similar controller or starting fresh. Property managers should ask for an itemized estimate so they can see the equipment and the labor separately. Call (866) 925-0168 for a walkthrough.
Do you work on the gate brand I already have?
In most cases, yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so you’re not stuck because a technician doesn’t recognize your system. We work on what you already have. Call (866) 925-0168 with the brand and model if you know it, and we’ll tell you what’s possible.
What happens when I call?
We answer the phone and talk through what’s going on with the gate. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. From there we schedule a look at the gate and give you a written estimate, free, before any work begins.
Why Call a Gate Specialist
Gate access control sits at the intersection of moving hardware and electronics, and it’s not the kind of thing a general contractor is set up to do. Waverly Gate Repair focuses exclusively on gates – repair, electric gate repair, and installation – so a technician arrives knowing how a controller talks to an operator, how an entry device is wired, and why a gate that runs fine one day starts faulting the next. That’s been our discipline since 2013, and it’s the whole reason we’re here.
We handle both repair and installation, so you’re not bounced between a fence company, an electrician, and an access control vendor. One specialist, one estimate, one company that owns the outcome. Whether you’re a homeowner in Lakewood whose driveway gate has stopped responding or a property manager with tenants locked out of the gate, we can take the call, come out, and get it sorted.
One more thing, because it matters: gates are heavy, and the operators and wiring that drive them carry real power. Work on control boards, low-voltage wiring, and gate operators should be done by a trained technician, not as a weekend project. We’re happy to tell you how your system works, but the actual electrical and operator work is best left to someone who does it every day.
Your gate, our only focus. Call (866) 925-0168 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Lakewood market as of 2026. Waverly Gate Repair offers free estimates – call (866) 925-0168.
Written by the team at Waverly Gate Repair, serving Lakewood since 2013.
What Our Customers Say
"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Eric Hayes"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Chris Parker"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Brandon Wong