Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Watts, CA
Gate installation in Watts usually means custom steel or chain-link work built for security on long, narrow lots with alley access. Most homes and small commercial parcels here need a gate fitted to an uneven old slab or packed soil, not a standardized kit. The heat, clay-heavy ground, and older housing stock change how posts are set and how frames are welded. If you need a gate repair or a new system planned from scratch, call (866) 925-0168. We answer 24/7.
Why Watts Homes Are Different
Watts is still a working-class, historically industrial South LA community. Housing runs heavily to single-story stucco and wood-frame homes from the 1920s through the 1950s, with detached garages, long driveways, and side-yard setbacks. That means most gates are not off-the-shelf units. They were welded to fit a specific opening, hung on posts somebody set years ago, and expected to hold up under hard daily use. Many are chain-link or heavy steel, and plenty were owner-fabricated or installed by a neighbor. We see sagging corners from leafs that weigh more than the hinges were rated for, latches that no longer line up after the ground shifted, and posts pulling loose from old concrete. The climate works against everything outside: hot, dry summers bake wood and dry out hinge hardware, while winter rains find failed paint and rust the weld joints. The soil here is clay-heavy, and steel posts expand and shift with the seasons. Long, narrow lots with alley access mean rear and side alley gates are usually the first line of security, and they take a beating. A gate company in Watts has to understand welding, sag correction, and security first, not just how to bolt on a pretty driveway unit.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Watts Services
Most calls in Watts come down to two problems: a gate that will not open or close properly, or an electric system that stopped responding. Here is how each one goes.
Gate Repair in Watts
A swinging steel gate that drags, a latch that will not catch, or a post that has pulled loose in clay soil is a security issue here, not a cosmetic one. Repair work in Watts often involves cutting and re-welding heavy leafs, replacing sagging hinges, and re-securing perimeter gates around driveways, side yards, and small business lots. The older the property, the more likely the original work was custom, which means every repair starts with understanding how the gate was built. For a full breakdown of what we fix and what it costs, see our Gate Repair in Watts page.
Electric Gate Repair in Watts
Automatic gate systems fail in predictable ways: a control board burns out, a limit switch drifts, a keypad stops reading, or a safety sensor gets knocked out of alignment. Electric gate repair requires a technician who understands the mechanical side and the electronics together, because the symptom is often not the cause. In Watts, many operators sit on older gates that have shifted, which forces the motor to work against misalignment until something gives. Read the specific symptoms and repair costs on our Electric Gate Repair in Watts page.
Gate Installation in Watts
New gate installation in Watts usually starts with a simple question: what is this gate actually protecting? On these lots it is often a long driveway, a side yard, or an alley entrance behind the house. The existing opening may be uneven, the old slab cracked, and the soil soft clay that moves with heat and rain. That means we plan the job around the site, not around a catalog. We build and install steel, chain-link, wood, and automated systems, and every job gets measured in person before we touch anything. Whether you are replacing something old or securing a property that never had a gate, our Gate Installation process covers the full scope from footings to final adjustments.
Driveway Gate Installation
Signs you need it
Your current driveway gate drags on the ground, no longer latches, or has posts leaning far enough that the gate cannot be adjusted back to square.
What it costs in Watts
A new driveway gate in Watts typically runs $1,800 to $6,500 depending on material, width, and whether you add an operator.
How we do it
We measure the opening, check the ground and existing footings, set new posts at proper depth, hang the leaf, and weld or bolt hardware so it swings square from day one.
Sliding Gate Installation
Signs you need it
A sliding gate has come off its track, binds when it moves, or you are converting a wide opening where a swing gate would take too much space.
What it costs in Watts
Sliding gate installation in Watts typically costs $1,600 to $4,400 for the steel frame, track, hardware, and ground preparation, before any automation.
How we do it
We lay out the track line, pour or reinforce the pad, set the track level, hang the gate, and adjust the rollers so it rolls without binding.
Automatic Gate Installation
Signs you need it
You want the gate to open from a keypad, remote, or phone instead of getting out of the car every time, or an existing operator has failed and needs a full replacement.
What it costs in Watts
Automatic gate installation in Watts runs $2,100 to $5,500 including the operator, safety edges, and programming, depending on the system and the gate weight.
How we do it
We mount the operator, run power from the nearest source, install safety edges and loops where required, then set limits and test the full cycle repeatedly.
What Gate Installation Costs in Watts
| Item | Typical range in Watts |
|---|---|
| Driveway gate, steel or wood, manual | $1,800 – $6,500 |
| Sliding gate, manual | $1,600 – $4,400 |
| Automatic gate system with operator | $2,100 – $5,500 |
How long does gate installation take in Watts?
Most residential gate installations are finished in one to two days. Custom welded steel, new concrete footings, and automation can push the job to three or four days, depending on curing time and the power run.
Do I need a permit for a new gate in Watts?
Many cities require a permit when a gate includes new electrical work or sits near the public right-of-way. We advise you to check with the city building department, and we plan the job to match what is approved before work starts.
Brands We Service in Watts
We work on what you already have. In Watts we service FAAC, BFT, Linear, and Viking operators among others, keeping common boards and parts stocked so a repair does not wait on a brand-specific dead end. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Watts, CA
| Service | Typical range in Watts |
|---|---|
| Gate repair, general | $120 – $750 |
| Gate installation, manual driveway | $1,800 – $6,500 |
| Gate installation, sliding | $1,600 – $4,400 |
| Automatic gate installation | $2,100 – $5,500 |
| Electric gate operator repair | $200 – $600 |
| Control board replacement | $300 – $800 |
| Hinge or weld repair | $150 – $400 |
| Post reset or replacement | $250 – $700 |
| Sensor or safety edge repair | $120 – $350 |
Prices in Watts push toward the higher end when a gate is oversized custom steel, the post footings are shot, or we have to cut out and re-weld significant sections. Whatever the job, we write the full price and agree on it with you before any work begins. The estimate is free, and the price on the written estimate is the price you pay.
Neighborhoods We Serve in Watts
We work across Watts and the surrounding blocks, from the residential streets near the historic towers to the commercial and industrial strips along the main corridors. Response time across the area is usually under an hour because we keep crews staged nearby.
- Central Watts
- Jordan Downs area
- Imperial Courts area
- Watts Junction
- South of 103rd Street
Service Area – Cities Near Watts
We serve Watts and the surrounding South LA communities. If you are nearby, we also work in Vermont Vista, CA, Bell Gardens, CA, Lakewood, CA, and West Whittier-Los Nietos, CA. Call and we will tell you exactly when we can be there.
Serving Watts, CA – Our Local Coverage Area
We serve Watts and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Watts
We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Same-day service is common when you call before midday.
Yes. A lot of Watts calls come from small commercial and industrial parcels that need a perimeter gate re-secured or an operator repaired. We work on the same brands and the same steel and chain-link construction used on those lots.
That is most of the gates in Watts. We do not need the original fabricator or a brand manual for a manual steel or chain-link gate. We assess the welds, hinges, post footings, and alignment, then repair what is actually failing.
Call (866) 925-0168 for a free estimate on any gate job in Watts. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60 minutes.
- 4You approve before work beginsNothing starts until you say go.
What Watts Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Ryan Barrett"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Adam Vaughn"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Kurt Bennett